Argus Analyzers AATPR10 Support
Downloads
Manuals
AATPR10 - Printer manual by language:
(for AATPR10 printer, AA500PWP tester/printer kit)
EN, FR, DE, NLN, ES, IT, CR, PT
AA500P tester product manual by language:
EN, FR, DE, NL, ES, IT, CR, PT
Manual Adendum:
(Programming custom printed report heading)
EN, FR, DE, NL, ES, IT, CR, PT
Declaration of Conformity: DoC
Warranty description by language:
EN, FR, DE, NL, ES, IT, CR, PT
Literature
AA Series brochure by language:
EN, NL, ES
AA Series small format brochure:
EN, DE, IT
Interpreting Display and Results
-
Is the paper for the AATPR10 and AATPR20 of a standard size available on the market?
-
Yes and no. The width of the paper is standard (58mm, 2.25in), as is the thickness (65u.) The diameter of the roll is non-standard at 23mm, 13/16in. You may purchase rolls of paper from Argus or from any Argus distributor. If you wish to source paper in bulk and prepare your own rolls, be sure to roll the paper such that the thermally active side of the paper faces the center of the roll.
-
How many test reports can be printed from one roll of paper?
-
Approximately 20 test reports can be printed from a single roll. Replacing the paper requires approximately 30 seconds.
-
Can more than one AA tester use the same printer?
-
The AATPR10 and AATPR20 printers can be attached or removed from a compatible tester AA500Pin a matter of seconds, much like a battery pack on a cordless drill. Technically one printer may be easily shared across a number of compatible testers.
-
How do I print a test report using an AA1000 Series tester?
-
First check that the AATPR20 printer is firmly attached to the base of the tester.
Second check that a roll of paper is installed properly in the printer and the natural curl of the paper is towards top of tester. A 'printer' icon should appear on the display indicating the printer is connected and ready to print. Please consult the Printer Manual for guidance.
Third, at any time after a test has been started, press and hold the center [enter/print] button (until beep.)
If a report does not print, check that 'Print' or 'Print - Save' is selected as the Output Mode in 'SETUP'. If 'Save' only is selected, the report is saved to memory, but not printed. See Tester Setup Options to view and change the Output Mode
-
Why are the printed test reports all blank?
-
The paper is installed backwards or the paper is not routed properly through the paper slot in the printer. Please consult the printer manual: AA500P series; AA1000/360 series.
-
I am trying to print, but the small print icon does not show in on the display, and I can not print.
-
The printer is out of paper or the paper is installed backwards. Install paper such that the natural curl of the paper is towards the top of the tester. Please consult the appropriate printer manual for paper installation guidance.
Troubleshooting
-
Is the paper for the AATPR10 and AATPR20 of a standard size available on the market?
-
Yes and no. The width of the paper is standard (58mm, 2.25in), as is the thickness (65u.) The diameter of the roll is non-standard at 23mm, 13/16in. You may purchase rolls of paper from Argus or from any Argus distributor. If you wish to source paper in bulk and prepare your own rolls, be sure to roll the paper such that the thermally active side of the paper faces the center of the roll.
-
How many test reports can be printed from one roll of paper?
-
Approximately 20 test reports can be printed from a single roll. Replacing the paper requires approximately 30 seconds.
-
Can more than one AA tester use the same printer?
-
The AATPR10 and AATPR20 printers can be attached or removed from a compatible tester AA500Pin a matter of seconds, much like a battery pack on a cordless drill. Technically one printer may be easily shared across a number of compatible testers.
-
How do I print a test report using an AA1000 Series tester?
-
First check that the AATPR20 printer is firmly attached to the base of the tester.
Second check that a roll of paper is installed properly in the printer and the natural curl of the paper is towards top of tester. A 'printer' icon should appear on the display indicating the printer is connected and ready to print. Please consult the Printer Manual for guidance.
Third, at any time after a test has been started, press and hold the center [enter/print] button (until beep.)
If a report does not print, check that 'Print' or 'Print - Save' is selected as the Output Mode in 'SETUP'. If 'Save' only is selected, the report is saved to memory, but not printed. See Tester Setup Options to view and change the Output Mode
-
Why are the printed test reports all blank?
-
The paper is installed backwards or the paper is not routed properly through the paper slot in the printer. Please consult the printer manual: AA500P series; AA1000/360 series.
-
I am trying to print, but the small print icon does not show in on the display, and I can not print.
-
The printer is out of paper or the paper is installed backwards. Install paper such that the natural curl of the paper is towards the top of the tester. Please consult the appropriate printer manual for paper installation guidance.
Solutions
Automotive Battery
Support